UDI Quadcopter Motor & Gears Disassembly – U818A DroneTube

Repair your Quadcopter UDI U818A, A-1 Discovery and U817. I explain how the motor and gears are assembled and disassembled in the arm and why its easier to replace the entire arm assembly instead of just replacing a bad motor.

UDI Spare Parts Kit: http://amzn.to/295CwWl

Here is a link to the video showing you how to replace the entire arm and motor assembly. This way there is no soldering involved! The procedure is the same for clockwise or anticlockwise arms. https://www.youtube.com/watch?v=-fYNdIUskFk

Buy the quadcopter here: http://amzn.to/1Aotvw3

Support Our Channel by bookmarking this link and use it whenever you shop on Amazon► http://www.amazon.com/?tag=hsra-20
Replacement Arm on Amazon for around $7 to $9: http://amzn.to/1NW8MIr

Propellers for the UDI U818A and 817: http://amzn.to/1OzNByV

Props for other Quads: http://amzn.to/1OzNF1C

UPGRADED UDI U818A-1 Quadcopter – Longer Flight Times, Upgraded Battery and Low Voltage Warning: http://amzn.to/1IXzOO9

Quadcopter Parts and Accessories:
Carrying Case for the U818A
http://amzn.to/1513adS

Neewer 3.7V – 1200mah Battery:
http://amzn.to/1wWRVOX

Quadcopter Charger:
http://amzn.to/1tSN276

Quadcopter Spare parts:
http://amzn.to/1pgJr2L

Websites
Review of SYMA X5C: http://thinqb.com/syma-x5c-quadcopter-drone-review/

Review of UDI U818A: http://thinqb.com/udi-u818a-quadcopter-drone-review/

Review of UDI U818A-1 (Upgraded Camera): http://thinqb.com/udi-u818a-discovery-upgraded-hd-camera-version/

Thanks again for watching and PLEASE SUBSCRIBE!!!

Audio Credit:
Transportation by Audionautix is licensed under a Creative Commons Attribution license (https://creativecommons.org/licenses/by/4.0/)
Artist: http://audionautix.com/

#drone #quadcopter #dronegear

34 Comments

  1. Bolulu Gamer on July 19, 2020 at 7:08 am

    ak aleti habire bozuluyor motor sürekli arza yapıyor .bunu üretinin amına koyayım emi

  2. Tim Pratt on July 19, 2020 at 7:08 am

    This video helped me replace the defective motor in my U818A-1 quad!! I was unsure about how to remove the housing at the end of the leg but once I watched this I was able to proceed with confidence that I wouldn’t break it. I swapped out the motors like a pro! It’s flying a lot better but clearly the bearings on the large gear are sticky, so I’ll have to replace either those or the whole arm at some point. Anyways, TYVM for the most instructional video, it was exactly what I was looking for 😀

  3. mick1027 on July 19, 2020 at 7:09 am

    Great! Thanks for making the video on the motor assembly.

  4. ThinCube on July 19, 2020 at 7:10 am

    I found this spare parts kit, has alot of the most common parts that break/fail and is not too much money: http://amzn.to/1UyLMmq

  5. josele21 on July 19, 2020 at 7:12 am

    Thank you very much or your video, it really helped me a lot. I crashed many times my u818 and now the left front motor (white prop) does not spin. I carefully removed the arm and looked at the wiring and realized the problem was the motor. Do you think it will be better to replace all 4 motors or just the broken one? I ordered the two front cc and ccw motor only and I am afraid i need them all. I ordered these http://www.ebay.com/itm/401055107622?_trksid=p2057872.m2749.l2649&var=670609817067&ssPageName=STRK%3AMEBIDX%3AIT. Great video, i subscribed.

  6. Eric Engquist on July 19, 2020 at 7:16 am

    I just got my discovery U818A. I am trying to get off the plastic cover on it. I unscrewed the 4 screws on the landing gear but the landing gear and motor are still solid in place. I don’t want to break it but how do you remove those so I can remove the plastic to work on the inside. (I have to replace the motor and stem.

  7. AMAGS COOKS on July 19, 2020 at 7:16 am

    hey I just installed my udi replacement arm and whenever I try to launch the drone it just pushes the drone to the replaced arm if u don’t understand what I’m saying I can send you a video of it but I’ve true everything please help

  8. Erik Rasmussen on July 19, 2020 at 7:18 am

    are both anti and clockwise the both same arms

  9. Erik Rasmussen on July 19, 2020 at 7:19 am

    i just ordered a arm for $7.59 for my white udi 818a drone

  10. Monu Girish on July 19, 2020 at 7:21 am

    Hello Sir drone fan nib wt tell name

  11. Mississippi Slim on July 19, 2020 at 7:22 am

    There is apparently to different versions of the U818a.  The battery voltages appear to be different.  The original version with the 2 wire RED connector is 3.5vdc,  the newer version with the 4 pin white connector is 7vdc.  I ordered replacement motors for a U818A and they go up in smoke after a single flight.  Do you know of a different part that is available for the U818A-1 Discovery FPV.

  12. fan of humor on July 19, 2020 at 7:25 am

    U818A motor fits for U919A quadcopter?

  13. bryan adams on July 19, 2020 at 7:28 am

    Awesome video.. helped me tons.. keep them coming.. where did you buy the whole arm assembly?? I paid 8.99 for 2 motors.. then had to buy a 40 dollar soldering kit..

  14. Erik Rasmussen on July 19, 2020 at 7:30 am

    how do i get the motor out on mu udi drone

  15. ThinCube on July 19, 2020 at 7:30 am

    Thanks for watching, please comment below and ask any questions you may have. I am always happy to help and respond as quickly as possible. I also made a video showing a pinout of all of the connectors on the PC Board: https://www.youtube.com/watch?v=BUghqOSFTiw Happy Flying!!!

  16. thegeist72 on July 19, 2020 at 7:32 am

    Thanks!

  17. Rahul Pasham on July 19, 2020 at 7:32 am

    Can you sell the moter and the gear under 100

  18. cahale06 on July 19, 2020 at 7:36 am

    I had a question maybe you can help. I just installed a new motor arm on my U818 and when I connect the battery to the copter that arm automatically turns on without the remote control and does not turn off until I disconnect the battery. Any ideas? Thanks

  19. Hector Manuel on July 19, 2020 at 7:37 am

    I changed the whole arm however now when I just plug in the battery the propeller starts spinning? any ideas??

  20. Brian Windle on July 19, 2020 at 7:38 am

    If you have burned up a motor, take a look at your board and/or plug one of the other motors into that socket first to see if you burned up the board too. Someone else commented about their rotor spinning constantly after replacement and I have the same issue (new motor spins as soon as you put the battery in, doesn’t respond to throttle). After verifying the new motor worked properly by plugging into a different socket I took a look at the board to find that a rectangular chip next to the socket (stamped 2300 on top, there is one for each motor) had burned up as well. Wish I would have checked this out before ordering a new motor! Haven’t been able to locate a replacement chip and doubtful I would even be able to solder it in properly. Can’t find a replacement board for this FPV/wifi version either. Total bummer.

  21. nawabkhan khan on July 19, 2020 at 7:41 am

    Hello sir i have issue on my db power u818a its doesn’t fly because there is no signal in the remote control..and when i searching for wifi there is no wifi plsss help me

  22. crabtrap on July 19, 2020 at 7:41 am

    very well thought out tutorial. you should do this professionally!

  23. Mississippi Slim on July 19, 2020 at 7:44 am

    This is the only 7.4v Micro Motor I was able to locate.  For reference the core resistance for the 3.7v motors is about 1ohm the 7.4v is about 2ohm.http://www.ebay.com/itm/2pcs-DC-7-4V-35000RPM-Electric-Micro-Coreless-Motor-6x14mm-for-RC-Helicopter-/231798034600?_trksid=p2141725.m3641.l6368

  24. ultra gamers on July 19, 2020 at 7:46 am

    Thanku bro if you have any ideas of udi rc drone please update to youtube

  25. Dave jones on July 19, 2020 at 7:47 am

    A great help as I got stuck, motor shaft removed okay, but was brought to a stop on how to remove the motor, had no idea that outer cover would slid off with a bit of help, much appreciated help, thank you.

  26. Barb Busch on July 19, 2020 at 7:48 am

    Nice Job! Thank you for posting this video. Very helpful

  27. ThinCube on July 19, 2020 at 7:50 am

    Hey everyone, right now thru Amazon the entire arm assembly is only $7 and change….here is a link to the clockwise: http://amzn.to/2ohcjfb and anti-clockwise: http://amzn.to/2oKn76s

  28. S N on July 19, 2020 at 7:51 am

    Hi …thanks for the video. Very helpful…my Quadcopter the wire going inside the motor (under the prop) is broken. Is it possible to repair it easily?

  29. Jessica Thomason on July 19, 2020 at 7:52 am

    Where would I go to get a replacement large white gear that turns the propeller?

  30. Diego Soriente on July 19, 2020 at 7:52 am

    Hi, I have a buy an engine for
    my drone udirc 818a fpv. I know it’s an 8520 but I do not know what revolutions per minute has that engine. Can you help me with that? I’m looking for information on the internet and I’m not finding anything. I do not want to buy something that does not work for me Then. thank you very very much!!!! Diego from Argentina

  31. OtroPl4n Argentina on July 19, 2020 at 7:57 am

    Someone can tellme the rpm’s of these motor?

  32. Puls point on July 19, 2020 at 8:02 am

    Can we get this gear box online

  33. Michael Younger on July 19, 2020 at 8:04 am

    hey man me again. the white rotars won’t turn, and if I flick them, they turn. I’ll post a video tomorrow if you don’t mind could you look at it please, thank you. I haven’t changed anything they just stopped spinning during flight and they turn off and on (white rotars)

  34. Stephen Spencer on July 19, 2020 at 8:06 am

    Your tutorial got me out of a pickle! Thank you.

Leave a Comment