How to install drone props correctly
How to install drone props correctly
A short video on how to properly install your props.
Amazon Influencer Shop https://www.amazon.com/shop/mstaffor1975
Find me on social media at:
Facebook – Mike’s Drones and More YouTube Discussion Group
Twitter – @MikesDroneMore
Instagram – mikesdronesnmore
Thank you so much you helped me fix my drone.
Thank you
question, I have a 3 inch alien with HQ props and the Lock nut does not go all the way down to the prop, it stops turning about halfway and leave space in between.. what should I do? I’m scared to break the motor
Thanks Mike!
I need help with my tyro 99 quadcopter drone im a beginner but have a little insight on theses things from past experience with other types please get back to be asap
Thanks
"Always ccw on the back right"??
Thanks for this. Very useful to someone starting out in fpv. Cheers from down under 🙂
You should mention it matters if you run prop in or prop out
Wow this is soo useful
Do you need to tighten the nuts down tight with a wrench or not
Hey Mike thanks for the cool little tip about that propellers. You simplify the entire process. I really wish there was a way to direct message on YouTube because I got a few questions. I finally sat down and forced myself to build a drone because I really want to learn what all the components did and how they work and what but now I’m left with more questions than I had to start with because not too many people controllers and power control boards and stuff like that. I was wondering if I could email you a couple questions I had about putting the final touches on my flight controller about to hook up and everything like that because the certain flight controller that I’m using in the power control board did I’m using there’s only one video and it’s all in Spanish and the guy speak through the entire video and installing everything so I can’t even mimic what I see him doing
Thank you very much Sir. You should have seen the joy from my daughter after the drone rose up after almost a year of down time due to drone blades mismatch
Thank you very much sir
How would you place the props on reversed motors ? 😀
Best explanation ever. Thank you.
How can you tell for drones where the props are on the bottom and you have to flip the drone over? I have skyviper spiderman homecoming drone that I got a while ago and I bought replacement props for it which are two sided and I haven’t figured out how to properly install them.
cool vid thanks!
Thanks Mike for the time you took for this video explanation.
It took me a month to figures this out but thanks to I don’t have to wait another month thank soo much
Thank you! This helped sooo much!
This is not a good video…..99% of drones come with clockwise props…….sure mr phantom
I run props out and like how it flies better, also the props don’t fling crap into the camera lens
awesome tutorial brother!!! man I know youre busy like everyone else but I would so much appreciate it if you would point me in the right direction on the best and cheapest way for what parts to get for a beginner. I have a couple regular drones (air hog mini racing drone and holy stone mini preditor drone which is awesome lol but I so want to get into building a FPV racing drone but have very little knowledge of then
How much you have to tighten
According two the echine wizard 220s it’s the opposite am I wright trying to not the props on. Mabe iam wrong idk anything about them
Thanks very much good explanation
This was really helpful, I pulled apart my drone to save it from water and didn’t marked the blades, now that i have learned the correct way i don’t have to worry about marking it anyway in future,
many thanks for the short helpful shortcut 🙂 R R R
Anton from Australia. New to droning and your tutorial helps a lot keep up the good work
Thank you your a life saver
Where do you get the things to screw to propeller onto the motor?
Is it included with the motor or with the props? Or do you need to buy these seperately?
Forgot to add the nut tightens the opposite way the prop spins. CW = Reverse thread, and CCW = Normal thread
In 99.9 percent I‘m still doing ist wrong
Thanks
Thank you for your good explanation 🙂
Thanks a lot your instruction was really good and help full.
Hey man, I may be wrong but it seems like the quad you pulled out at 6:25 has its front right prop on backwards
THANK YOU! Exactly WTF I was looking for, you rock, Haus!
Do you know anything about the amerteer mini drone props
What props is good for the motor k2204-kv2300 and esc and baterry all together let me know please
Whilst this was very helpful (thank you) it is only half the story. Many of us need explanations about the nut direction – which counter intuitively all seem to be the same way on mine – and how much to tighten the nuts. Do I need to buy a torque driver? Set to what, please?
Edit: If, like me you are complete noob then there is a better video here:
https://www.youtube.com/watch?v=uzArH7KV5Z0
Did he really just spend 9 minutes talking about clockwise and counter clockwise motion of four props? What a waste of time. 30 second video max. Didn’t even torque the screws. Fml
Thank you so much i thought that it has broken by after watching your video it help me thankyou so much
Great content. Thanks so much. I hadn’t a notion about the right way to put the probs on my hawk 5
thank you you just saves me a expensive mistake 🙂
Thanks bro
Sub to the great explain
Is it the same if I didn’t get the drone for Christmas?
If that’s the case, then it doesnt matter if camera is facing toward or away from you.