GoPro: Karma Replacement Parts – Arms

GoPro: Karma Replacement Parts – Arms

Replacing an arm on Karma can be done in less than 20 minutes. There are four main steps: removing the landing gear, removing the old arm, installing the new arm, reattaching the landing gear. In this video, we’ll walk you through each step.

For more details, visit

Preflight – Overview + Charging (
Preflight – Assembly (
Preflight – Preparing for Flight (
Preflight – Safety (

In Flight – Taking Off (
In Flight – Capturing (
In Flight – Landing (

Auto Shot Paths – Cable Cam (
Auto Shot Paths – Dronie (
Auto Shot Paths – Orbit (
Auto Shot Paths – Reveal (

Replacement Parts – Arms (You Are Here)
Replacement Parts – Karma Stabilizer (
Replacement Parts – Karma Harness (
Replacement Parts – Landing Gear (

Karma – Safety Features (

As always, happy capturing!

You might see examples of extreme use in this video. Please take appropriate precautions to ensure your own safety and the safety of those around you, and to protect your GoPro camera.


  1. Phillip Kidd on July 24, 2021 at 8:31 pm

    Is it common for one arm red light to blink while in flight this just started

  2. jamesb72 on July 24, 2021 at 8:37 pm

    is the esc also in the arm – hope so as that covers both common breakages.

  3. Justin on July 24, 2021 at 8:40 pm

    Let’s be honest… we’re all here for very unfortunate reasons.

  4. El pollo Loco on July 24, 2021 at 8:43 pm

    Mine keeps saying fully extend arms 🤷🏻‍♂️,somebody help please

  5. Josh! Tulberg on July 24, 2021 at 8:48 pm

    I wonder what electronics are in the landing gear?

  6. Sam L Edmunds on July 24, 2021 at 8:51 pm

    Bollocks. The arms don’t go on at all

  7. Ten Ten on July 24, 2021 at 8:53 pm

    Xuất bản 24 thg 4, 2019

  8. Will Brown on July 24, 2021 at 9:04 pm

    Great video thanks

  9. t105x104 on July 24, 2021 at 9:05 pm

    I just had to remove an arm and found this video useful. I didn’t however have a replacement arm or screwdriver. I used a #2 allan key and pressed down firmly as I undid the screws. This worked just fine. To release the power cable I used a flathead screwdriver to push against the side of the plug as I gently pulled the plug upward, using the white straps. I have learned that I must calibrate the drone before every flight, not just when prompted by the controller and only operate in open areas. I hope this comment helps other Karma pilots!

  10. Fabiancho Slzh on July 24, 2021 at 9:08 pm

    Que triste cuando se rompe …

  11. Russell Grant on July 24, 2021 at 9:11 pm

    TIps for installing.

    1. They provide a tool to unscrew. The screw will strip very easily if you try your own.
    2. When putting the arm back on. They give you some screws. One of the them is slightly longer. Use that one to install.

  12. sumit mitra on July 24, 2021 at 9:12 pm

    Which screwdriver can be used?

  13. el cubo proyecto on July 24, 2021 at 9:14 pm

    Hi guys! I need help, I just crushed my karma, I changed the broken propellers. And It has a small scratch on the landing gear but it’s ok … but when I’m trying to take off there’s a message "a problem detected" and it doesn’t works.

  14. Eric R. Gonzalez on July 24, 2021 at 9:14 pm


  15. Dee Dart on July 24, 2021 at 9:15 pm

    Second…. karma looks cool

  16. Seim Kuruc on July 24, 2021 at 9:18 pm

    Wish I would have seen this before I painted mine.. would have made for much less masking work, and I would have painted the arms as well instead of only the top case..

  17. Steve Bucher on July 24, 2021 at 9:19 pm

    where can you buy replacement parts?

  18. SUT NGAI AUNG on July 24, 2021 at 9:20 pm

    How do I know which part is broken ? Actually I have a problem , I think it’s motors but I don’t know which part has a problem.All propellers are spinning very well, Karma and controller also. However when I flew, it goes right side not up !
    Can you give me suggestions?

  19. Michael Monnin on July 24, 2021 at 9:21 pm

    Needed a Chapman tool to get the hex fasteners secured.

  20. Anne Brecount on July 24, 2021 at 9:28 pm

    I did not get the screwdriver or release tool in the package. Can I do this without it?

Leave a Comment